KAIST Lithium-Sulfur Electrode Survives 1,000 Bends for Drone Legs
KAIST and Chalmers researchers built a lithium-sulfur cathode that kept 94.0% of its flat capacity when curved, but the pouch cells are lab prototypes that only lit an LED in a drone-leg shape.
2 min read

A curved lithium-sulfur pouch cell from KAIST and Chalmers kept 94.0% of its flat-state capacity in lab tests.
Graphic: Voltgrid News
Researchers at KAIST (Korea Advanced Institute of Science and Technology) and Chalmers University of Technology have built a lithium-sulfur battery electrode that survived 1,000 bending cycles at a 2.5 mm radius, so a drone leg could one day store energy as well as carry load. KAIST announced the work on Nov. 18, 2026, and the paper was published online on Oct. 1, 2026 in the peer-reviewed journal Advanced Composites and Hybrid Materials.
In the paper, first author Jawon Ha, Professor Il-Kwon Oh of KAIST's Department of Mechanical Engineering and Professor Leif E. Asp of Chalmers describe growing nickel cobalt selenide (NiCo2Se4) nanowires directly on woven carbon cloth. In a lithium-sulfur cell, sulfur in the cathode does the storing, and the nanowires help hold on to the sulfur compounds that otherwise dissolve away. The paper reports 1,544 mAh per gram of sulfur at 0.1 C, a slow discharge rate. KAIST has been busy on batteries this month, as Voltgrid News reported on its lithium-metal separator.
How the electrode copes with curved parts
Most structural battery designs are flat. Drone legs and robot frames are often curved or hollow, and a stiff cathode can crack or peel when it is bent and loaded. Here the nanowires are grown on the carbon fibers rather than coated onto them, and the authors say this keeps the electrode connected after 1,000 bends at 2.5 mm.
The curved cell held up in the numbers too. A pouch cell bent into a cylinder delivered 1,117 mAh per gram at 0.02 C, which is 94.0% of its flat-state capacity of 1,188 mAh per gram. In a separate test, a cell inside a polylactide plastic frame kept about 99.8% of its voltage while the frame itself fractured under load; the paper puts the voltage change at roughly 5 mV, from 2.457 V to 2.452 V. That figure is voltage, not capacity.
Bent into a cylinder, the lab cell delivered 94.0% of its flat-state capacity, at a low sulfur loading of about 1 mg per square centimeter.
Graphic: Voltgrid News
What the demonstration does not show
The oval, square, cylindrical and drone-leg versions each powered an LED, according to Tech Xplore, which republished KAIST's release. No flight test is reported. The curved-capacity test used a sulfur loading of about 1 mg per square centimeter, a controlled baseline the authors chose, and the paper itself says a practical cell also needs high sulfur loading, lean electrolyte and long-term cycling stability. The longer cycling run, in a coin cell, covered 250 cycles.
The researchers say further work is needed to learn how much weight a structural battery could save and how much flight or operating time it could add. Combining the electrode with load-bearing composites is a next step, not a tested result. Professor Oh said the study shows drone legs and robotic frames could serve as both structural parts and energy storage. For drone and robot makers, the open question is how much weight and volume removing a separate battery pack would save, and no source gives a figure or a date for that yet.
Sources
- 01Structural battery electrode enables energy storage inside curved drone legsPhys.org · energy and green techtechxplore.com
- 02Monolithically integrated NiCo2Se4 nanowire-carbon cloth cathode scaffolds for non-planar lithium-sulfur structural-battery integrationAdvanced Composites and Hybrid Materials (Springer Nature)link.springer.com
- Desk
- Science Desk
- Published
- Sources
- 2 cited



